Car rear suspension Mercedes Vito 2 (W639)

Rear suspension
The rear suspension of Vito Viano cars is an independent suspension with longitudinal arms. Each of the levers is attached using two silent blocks to brackets located on...

Rear suspension with metal springs
VN 5.011 1. Rear spring; 2. Rear suspension buffer; 3. Shock absorber; 4 Bushing; 5. Rubber bushing; 6. Rubber bushing; 7. Bolt securing the shock absorber to the lever;...

Rear air suspension
The main elements of the air suspension are: pneumatic spring; compressor; piping and valve system; air suspension control unit; body level sensor. VN 5.012 1. Pneumatic...

Air suspension compressor
The air suspension compressor is attached to the bottom of the car body using a special bracket. The compressor is connected to the control system via an electrical...

Rear air suspension lines
VN 5.014 1. Solenoid valve; 2. Air duct; 3. Screw; 4. Rubber bushing; 5. Filter; 6. Plastic clamp; 7. Clamp for fastening wiring; 8. Clamp; 9. Clamp; 10. Clamp; 11....

Rear stabilizer
The rear anti-roll bar is designed to counteract the vehicle's roll when cornering or driving on a slope. The rear anti-roll bar interacts with the front anti-roll bar....

Removal and installation the rear shock absorber
To remove the rear shock absorber, use a jack to compress the suspension spring, lifting the rear arm, and unscrew the bolts (4) and (5). VN 5.017 1. Body; 2. Rear...

Checking the condition of the rear shock absorber
The lower rubber-metal joint of the shock absorber is not suitable for further use (crushing and wear of the rubber part of the hinge). VN 5.018 The lower rubber-metal...

Removal and installation rear suspension arms
To remove the rear suspension arm, follow these steps:. - Remove the protective cap of the central hub nut. - Having braked the wheel securely, loosen the central nut of...

Removal and installation the rear hub bearing
VN 5.024 1. Bushing; 2. Wheel hub; 3. Bearing ring; 4. Retaining ring; 5. Brake disc protective plate; 6. Old bearing; 7. New bearing Removal - Remove the rear...

Removal and installation the rear axle thrust rod
VN 5.025 1. Rear gearbox; 2. Bolts for fastening the reaction rod to the body; 3. Bolts for fastening the reaction rod to the gearbox; 4. Jet thrust; 5. Rubber bushing

Replacing the rear gearbox oil seal
VN 5.026 1. Gearbox seal; 2. Rear gearbox; 3. Retaining ring Caution: When installing, do not damage the seal seating surface and the spring ring of the new seal.

Checking and adjusting rear wheel alignment
Since the rear wheel suspension is independent, the rear wheel alignment angles should be checked. There are two values related to the rear wheel alignment angles:...

Checking the rear wheel alignment
The rear wheel camber is not adjustable. Checking the camber is required to monitor the condition of the rear suspension elements and the suspension mounting elements to...

Removal and installation the steering gear
VN 6.001 1. Steering gear housing; 2. Steering rod; 3. Steering rod boot; 4. Tie rod end; 5. Bolt; 6. Washer; 7. Bolt; 8. Nut; 9. Nut Vito Viano vehicles use a...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More similar sections for repairing other models

☛ Chassis: Rear suspension car Mercedes W123 (1976-1985)
☛ Chassis: Rear suspension car Mercedes W463 (1999-2019)
☛ Chassis: Rear suspension car Mercedes W163 (1997-2005)
☛ Chassis: Rear suspension car Mercedes W116 (1972-1980, petrol)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code

Vito 1 (1996-2003)