Car rear suspension Mercedes M-Class (W163)
The rear suspension is fully independent. The rear axle assembly is formed by a torsion bar/anti-roll bar and two lower triangular wishbones connected by a subframe. The suspension of the bridge is organized by means of two shock absorber struts with coil springs, upper transverse triangular levers and two longitudinal extensions.
Removal and installation of the rear axle assembly
Rear Axle Assembly Installation Details 1 - Subframe; 1h - Parking brake cable support bracket; 1p - Control link; 55 - Rear differential crankcase ventilation hose; 109...
Rear Axle Assembly Installation Details 1 - Subframe; 1h - Parking brake cable support bracket; 1p - Control link; 55 - Rear differential crankcase ventilation hose; 109...
Removal, disassembly and installation of rear struts
Note: All self-locking bolts and nuts must be replaced! Removal Rear Suspension Strut Assembly Installation Details 67 - Lower wishbone; 67a - Nuts; 67b - Bolts; 73 -...
Note: All self-locking bolts and nuts must be replaced! Removal Rear Suspension Strut Assembly Installation Details 67 - Lower wishbone; 67a - Nuts; 67b - Bolts; 73 -...
Removal and installation the torsion bar
Rear suspension torsion bar installation details 77 - Torsion bar; 77a - Rubber bushing; 77b - Clamp; 77c - Bolts; 78a - Connecting bolt; 78b - Bearing; 78c - Bearing;...
Rear suspension torsion bar installation details 77 - Torsion bar; 77a - Rubber bushing; 77b - Clamp; 77c - Bolts; 78a - Connecting bolt; 78b - Bearing; 78c - Bearing;...
Removal and installation the lower wishbone
Rear suspension lower wishbone installation details 6j - Rackmount assembly; 7a - Lower ball joint; 94 - Lower wishbone; 125a - Bearing with nut; 125b - Bearing; 125 -...
Rear suspension lower wishbone installation details 6j - Rackmount assembly; 7a - Lower ball joint; 94 - Lower wishbone; 125a - Bearing with nut; 125b - Bearing; 125 -...
Removal and installation the upper wishbone
Rear Upper Wishbone Installation Details 6j - Rackmount assembly; 91 - Upper wishbone; 91a - Upper ball joint; 91b - Axle bolts; 111 - Brake Caliper (do not...
Rear Upper Wishbone Installation Details 6j - Rackmount assembly; 91 - Upper wishbone; 91a - Upper ball joint; 91b - Axle bolts; 111 - Brake Caliper (do not...
Removal and installation the longitudinal stretcher
Rear suspension longitudinal strut installation details Note: All self-locking bolts and nuts must be replaced! 1. The details of the installation of the longitudinal...
Rear suspension longitudinal strut installation details Note: All self-locking bolts and nuts must be replaced! 1. The details of the installation of the longitudinal...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
More similar sections for repairing other models
☛ Chassis: Rear suspension car Mercedes W123 (1976-1985)
☛ Chassis: Rear suspension car Mercedes W463 (1999-2019)
☛ Chassis: Rear suspension car Mercedes W126 (1979-1991, petrol)
☛ Chassis: Rear suspension car Mercedes Vito 2 (2003-2014, diesel)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Introduction to the guide
- Controls and instruments
- Driving and operation
- Maintenance
- Power unit
- Gasoline engines
- Diesel engines
- Cooling system
- Heating and ventilation
- Power system (gasoline)
- Fuel system (diesel)
- Exhaust system
- Ignition and control system
- Charging and starting system
- Transmission
- Mechanical gearbox
- Automatic gearbox
- Clutch
- Drive shafts and cardan
- Transfer case
- Chassis
- Brake system
- Front suspension
- Rear suspension
- Steering
- Suspension geometry
- Body
- Exterior (external elements)
- Interior (internal elements)
- Doors and locks
- Electrical equipment
- Equipment and devices
- Drive motors
- Lighting and signaling
- Audio system
- Electrical circuits