Rear suspension and wheels of the car Mercedes Vito 1 (W638)

Removal and installation the rear suspension
Removal 1. Remove the wheel. Before raising the vehicle, loosen the wheel nuts. 2. Unscrew nut 11 securing hub 6 and unscrew bolts 10 (see figure 7.12). Figure 7.12....

Lower suspension arm
Removal 1. Set the vehicle to "Service Position" (only cars with rear air suspension). 2. Disconnect the negative cable from the battery. 3. Remove hub 6 (see figure...

Anti-roll bar (cars 638.244 from 1.4.97 with air suspension of rear wheels)
Removal 1. Remove the clamps 1 and rubber bushings 2 that attach the stabilizer 3 to the frame (see figure 7.14). Figure 7.14. Anti-roll bar (cars 638.244 from 1.04.97...

Air suspension control unit
Removal 1. Lower the right seat 9 (see figure 7.15). Figure 7.15. Air suspension control unit: 1. Service switch, 2. Interior cladding, 3, 4, 8. Bolts, 5. Support, 6....

Removal the shock absorber
1. Unscrew bolt 4 securing the shock absorber to the lower arm (see figure 7.16). Figure 7.16. Shock absorber: 1. Shock absorber, 2. Service switch, 3, 4. Bolts. 2....

Air chamber (vehicles 638.0/1 and 638.2 with air suspension of rear wheels)
Removal 1. Set the car to "Service mode" (only on vehicles with air suspension). Press button 1 at the bottom for about 2 seconds before lifting. 2. Raise and secure the...

Checking and adjusting the vehicle level
Removal 1. Connect the 087 tester to the diagnostic connector (see figure 7.18). Figure 7.18. Checking and adjusting the vehicle level: 1. Adjusting device, 2. Pneumatic...

Compressor — removal and installation
Removal 1. Set the car to "Service mode" (only on vehicles with air suspension). Press button 1 at the bottom for about 2 seconds before lifting (see figure 7.19)....

Lift height sensor (vehicles 638.0/1 and 638.2 with rear wheel air suspension)
Removal 1. Set the car to "Service mode" (only on vehicles with air suspension). Press button 1 at the bottom for about 2 seconds before lifting (see figure 7.20)....

Height sensor adjustment lever
Removal 1. Set the car to "Service mode" (only on vehicles with air suspension). Press button 1 at the bottom for about 2 seconds before lifting (see figure 7.21)....

Camber and longitudinal inclination of the front wheel kingpin
General information The longitudinal inclination of the kingpin is set by the manufacturer. Changing its value can be achieved by changing the camber of the wheels....

Front wheel alignment
1. Set the wheels to straight ahead and install the lock 1 (see figure 7.23). Figure 7.23. Set the wheels for straight-line movement and install the lock 1. 2. Check and...

Rear wheel alignment
Loosen the eccentric bolt 1 and adjust the camber and toe by turning the nut on the lever 2 (see figure 7.26). The values of the camber and toe angles of the rear wheels...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More similar sections for repairing other models

☛ Chassis: Rear suspension car Mercedes W123 (1976-1985)
☛ Chassis: Rear suspension car Mercedes W463 (1999-2019)
☛ Chassis: Rear suspension car Mercedes W163 (1997-2005)
☛ Chassis: Rear suspension car Mercedes W220 (1998-2005)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code

Vito 1 (1996-2003)