Contents: Adjusting the position of the…↡ Exterior rear view mirrors ↡ Saving the mirror position to memory ↡ Position of the outside rearview…↡ Saving the adjusted mirror position…↡
Adjusting the position of the steering wheel
There is a risk of accident!
For safety reasons, do not change the position of the steering wheel while driving.
Also, when leaving the car for a short time, remove the electronic key from the ignition or take the smart card with you.
However, it is also possible to adjust the steering wheel position when the driver's door is open. Therefore, do not leave children unattended in the car.
Turn the electronic key in the ignition switch to position 1 or 2.
With the driver's door open and the electronic key removed, the steering wheel position can be adjusted; after closing the driver's door or inserting the electronic key into the ignition switch, this position is reset and the steering wheel returns to the stored position.
The lever is located on the steering column.
- 1 Longitudinal movement of the steering column
Press the lever forward or backward.
- 2 Steering column height
Press the lever up or down.
Note: The steering wheel position can be stored in memory along with the position of the seats and mirrors. (Memory function - discussed in Section Seat position memory).
Exterior rear view mirrors
The buttons are located on the driver's door.
The exterior rear-view mirrors are spherical, which expands the field of view.
There is a risk of accident!
The outside rearview mirrors give a reduced image. Objects appear more distant.
Adjusting the position of the outside rearview mirrors
Turn the electronic key in the ignition switch to position 2.
Mirror selection:
- On the driver's side - press button "1".
- On the passenger side - press button "2".
Press the adjustment switch "3" as needed, top, bottom, left or right.
Note: At low outside temperatures, the mirrors are heated automatically.
Saving the mirror position to memory
Models with memory function
Along with the position of the outside mirrors, store the position of the inside rearview mirror, seats and steering wheel. (The memory function is discussed in Section Seat position memory).
Position of the outside rearview mirror when parking, on the front passenger side
Models with memory function
Turn the electronic key in the ignition switch to position 2.
Text republished from the website www.MercedesMan.ru
Press button "2".
Engage reverse gear.
The outside rearview mirror rotates to its original position if:
- reverse gear is disengaged - after about 10 seconds;
- the speed limit of 10 km/h is exceeded - immediately, regardless of the gear engaged;
- button "1" is pressed.
Saving the parking mirror position to memory: Turn the electronic key in the ignition switch to position 1 or 2.
The car must be stationary.
Press button "2" and position the mirror on the edge of the curbstone.
Press memory button "4".
Press the adjustment switch "3" at the bottom for 3 seconds.
The mirror should not change its position.
If the mirror changes position, repeat the memory recording.
Note: For each electronic key or for both smart cards, it is possible to store one parking position in the memory.
Electrically adjustable inward-facing exterior rear-view mirrors
The buttons are located on the driver's door.
- 1 Turn outwards
- 2 Turn inwards
Note: Mirrors may vibrate if not fully extended.
Caution! If the mirror housing has been forcibly pulled forward from its locking position (in the direction of movement), then fix it again by pressing firmly.
If the mirror housing was forcibly pulled out of the locking position backwards, then to turn the mirror inward, press button "2".
After this, the mirror can be adjusted again to the driving or parking position.
Driver's side exterior rearview mirror with automatic glare reduction
Reducing the glare effect: Turn the electronic key in the ignition switch to position 2.
Depending on the angle of incidence of light, the driver's side exterior rearview mirror automatically switches the anti-glare function on or off.
There is a risk of accident!
The automatic glare reduction function is limited if light does not fall unobstructed on the sensors of the interior rearview mirror, for example when the rear window blind is raised or when driving with a trailer.
Note: When reverse gear is engaged or the interior light is on, the driver's side outside rearview mirror does not reduce glare.
Interior rearview mirror with mechanical anti-glare function
Adjust the mirror position manually.
Glare reduction: Using the glare reduction lever "1".
Interior rearview mirror with automatic glare reduction
Adjust the mirror position manually.
Reducing the glare effect: Turn the electronic key in the ignition switch to position 2.
Depending on the angle of incidence of light, the interior rearview mirror automatically switches the glare reduction function on or off.
There is a risk of accident!
The automatic glare reduction function of the interior rearview mirror is limited if light does not fall on the interior rearview mirror sensors unimpeded, for example when driving with a trailer.
Note: When reverse gear is engaged or the interior light is on, the glare reduction function on the interior rearview mirror is disabled.
Saving the adjusted mirror position to memory
Models with memory function
Along with the position of the interior rearview mirror, store the position of the exterior rearview mirrors, seat positions and steering wheel. (The memory function is discussed in Section Seat position memory).