Brake system of the car Mercedes S-Class (W140)

General information and safety precautions
General information The hydraulic brake system consists of a master brake cylinder, a brake booster, and front and rear disc brakes. The brake system has two circuits....

Brake system specifications
Note: Individual characteristics are also given in the text of the Chapter and, if their implementation is mandatory, are highlighted in bold. General parameters Design...

Location of ASR/ETS traction control system components
ASR/ETS traction control system component layout diagram A1e17 - ABS malfunction indicator lamp; B24/2 - Lateral acceleration sensor (140.04/05/06/07); K20/1 - Pump...

Location of Brake Assist System (BAS) components
Layout of the components of the emergency braking booster BAS 1 - Master brake cylinder; 2 - Vacuum pipe; A1e17 - ABS malfunction indicator lamp; A1e39 - Signal lamp EA;...

Location of ESP system components
Layout of ESP system components A1e17 - ABS malfunction indicator lamp; A1e41 - ESP warning light; A1e42 - ESP malfunction indicator lamp; A1e43 - EPC fault indicator...

Disassembly and assembly of the main brake cylinder of the «Tandem» type (models 140.028/032/033/135)
Design of the "Tandem" type GTZ 3, 7, 20 - Pistons; 5 - Retaining ring; 8 - Locking plate; 9 - Traffic jams; 10 - Reservoir; 22 - Body; 27 - Guide pin Disassembly 1....

Removal, installation and checking of the functioning of the brake booster servo drive
Removal Brake booster servo installation details 1. Remove the brake master cylinder (see section Disassembly and assembly of the main brake cylinder (MBC) of the...

Removal and installation the brake caliper
Front wheel brake caliper Removal Front Wheel Brake Caliper Installation Details 1. Remove the front wheels. 2. Disconnect the brake hose (51) from the brake pipe (5)...

Checking the thickness of the brake disc and brake pads
Checking the thickness of the brake disc (61) and brake shoe linings (43) 1. Raise the vehicle. 2. Remove the wheels. 3. Check the thickness of the brake shoe linings...

Removal and installation parking brake shoes
Removal Removal and installation of brake pads on models produced since 01.11.93. Removal and installation of brake pads on models produced up to 10/31/93. 1. Remove the...

Removal and installation the front parking brake cable
Removal Removal and installation the front parking brake cable 1. Remove the exhaust system heat shield. 2. Remove the return spring (94). 3. Loosen the adjusting bolt...

Adjusting the parking brake
Models before 01.11.93 Adjusting the parking brake on models 140 up to 10/31/93. 1. Raise the rear of the vehicle. 2. Remove one bolt on each rear wheel. 3. Using a...

ABS Wheel Sensors — Installation Details
Front Wheel Speed Sensor Installation Details L6/1a, L6/2a — Sensor mounting bolts L6/1, L6/2 — Front wheel speed sensors L6/1b, L6/2b — Bushings Front and rear wheel...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More similar sections for repairing other models

☛ Chassis: Brake system car Mercedes W168 (1997-2004)
☛ Chassis: Brake system car Mercedes 190 (W201) (1982-1993)
☛ Chassis: Brake system car Mercedes W210 (1996-2002)
☛ Chassis: Brake system car Mercedes W463 (1999-2019)
☛ Chassis: Brake system car Mercedes W163 (1997-2005)
☛ Chassis: Brake system car Mercedes Vito 2 (2003-2014, diesel)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code

W140 (1991-1998)