Brake system of the car Mercedes A-Class (W168)
Brake system specifications
Technical data of the brake system Disc brakes front front front front rear Vehicle type 168.006/007/031 168.006/009/033/108/109/131/133 410.600/700 (VANEO)...
Technical data of the brake system Disc brakes front front front front rear Vehicle type 168.006/007/031 168.006/009/033/108/109/131/133 410.600/700 (VANEO)...
General description of the braking system
The hydraulic brake system consists of a master cylinder, a vacuum brake booster, an anti-lock braking system and front and rear wheel brakes. The braking system is...
The hydraulic brake system consists of a master cylinder, a vacuum brake booster, an anti-lock braking system and front and rear wheel brakes. The braking system is...
Disc brake pads — removal, inspection and installation
This chapter describes the procedure for removing, checking and installing the brake pads of the front disc brakes. Removing the rear brake pads is generally similar....
This chapter describes the procedure for removing, checking and installing the brake pads of the front disc brakes. Removing the rear brake pads is generally similar....
Support — removal and installation
This chapter describes the procedure for removing and installing the front brake caliper. Removing the rear brake caliper is generally done in the same way. Features...
This chapter describes the procedure for removing and installing the front brake caliper. Removing the rear brake caliper is generally done in the same way. Features...
Front Brake Disc — Removal and Installation
To ensure uniform braking of the front wheels, both brake discs must have equally ground surfaces with the same degree of roughness. Therefore, be sure to replace or...
To ensure uniform braking of the front wheels, both brake discs must have equally ground surfaces with the same degree of roughness. Therefore, be sure to replace or...
Rear Brake Disc — Removal and Installation
Be sure to replace or grind both brake discs of one axle at the same time. Attention! If the brake discs are being modified, then the brake pads must also be replaced...
Be sure to replace or grind both brake discs of one axle at the same time. Attention! If the brake discs are being modified, then the brake pads must also be replaced...
Brake disc — check
1. Mark the position of the wheels on the hub with paint. This will allow you to install the balanced wheel in its original position during assembly. 2. Loosen the wheel...
1. Mark the position of the wheels on the hub with paint. This will allow you to install the balanced wheel in its original position during assembly. 2. Loosen the wheel...
Parking brake pads — removal and installation
On vehicles with disc brakes, the brake drum for the parking brake shoes is combined with the brake disc. Removal 1. Mark the position of the rear wheels on the hubs...
On vehicles with disc brakes, the brake drum for the parking brake shoes is combined with the brake disc. Removal 1. Mark the position of the rear wheels on the hubs...
Parking brake — adjustment
The parking brake must be adjusted in cases where the proper holding effect is not achieved when the parking brake lever is tightened more than 3 teeth of the sector. 1....
The parking brake must be adjusted in cases where the proper holding effect is not achieved when the parking brake lever is tightened more than 3 teeth of the sector. 1....
Front Parking Brake Cable — Removal and Installation
Removal 1. Turn off the ignition. 2. Release the parking brake. 3. Remove the rear part of the center console, see the relevant chapter . 4. Place the vehicle on jack...
Removal 1. Turn off the ignition. 2. Release the parking brake. 3. Remove the rear part of the center console, see the relevant chapter . 4. Place the vehicle on jack...
Rear Parking Brake Cable — Removal and Installation
Removal 20. Release the parking brake. 21. Place the vehicle on jack stands. Warning! Jacking up the vehicle and placing it on stands may pose a risk of injury. Read the...
Removal 20. Release the parking brake. 21. Place the vehicle on jack stands. Warning! Jacking up the vehicle and placing it on stands may pose a risk of injury. Read the...
Brake shoes of drum brake mechanism — removal and installation
The rear wheel drum brake mechanism is set automatically. The plunger of the adjusting mechanism extends and provides a constant gap between the brake drum and the...
The rear wheel drum brake mechanism is set automatically. The plunger of the adjusting mechanism extends and provides a constant gap between the brake drum and the...
Brake fluid — safety precautions
Caution! When handling brake fluid, keep the following in mind: a) Brake fluid is poisonous. It should never be sucked out by mouth through a hose. Pour brake fluid only...
Caution! When handling brake fluid, keep the following in mind: a) Brake fluid is poisonous. It should never be sucked out by mouth through a hose. Pour brake fluid only...
Brake system — bleeding
After any brake repair in which the brake system was opened, air may enter the hydraulic pressure lines. In this case, it is necessary to remove this air from the brake...
After any brake repair in which the brake system was opened, air may enter the hydraulic pressure lines. In this case, it is necessary to remove this air from the brake...
Brake hoses — removal and installation
The brake system pipes are the connecting line between the master brake cylinder and the working brake mechanisms of the wheels. Attention! The installation of metal...
The brake system pipes are the connecting line between the master brake cylinder and the working brake mechanisms of the wheels. Attention! The installation of metal...
Brake booster vacuum — check
The force applied by the driver to the brake pedal is increased by the brake booster. In petrol models, the low pressure required for this is taken from the intake...
The force applied by the driver to the brake pedal is increased by the brake booster. In petrol models, the low pressure required for this is taken from the intake...
Brake Light Switch — Removal and Installation
1. Check the brake light switch, see the relevant chapter . The brake light switch is located above the brake pedal on its bracket (see illustration 15.3). Removal 2....
1. Check the brake light switch, see the relevant chapter . The brake light switch is located above the brake pedal on its bracket (see illustration 15.3). Removal 2....
Parking Brake Indicator Light Switch Sensor
When the parking brake is applied, two indicator lights on the instrument panel come on. The switch for the lights is located on the back of the parking brake handle....
When the parking brake is applied, two indicator lights on the instrument panel come on. The switch for the lights is located on the back of the parking brake handle....
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
More similar sections for repairing other models
☛ Chassis: Brake system car Mercedes W202 (1993-2000)
☛ Chassis: Brake system car Mercedes W210 (1996-2002)
☛ Chassis: Brake system car Mercedes W463 (1999-2019)
☛ Chassis: Brake system car Mercedes W163 (1997-2005)
☛ Chassis: Brake system car Mercedes W126 (1979-1991, petrol)
☛ Chassis: Brake system car Mercedes Vario 814D (1996-2003, diesel)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Troubleshooting
- Power unit
- Engine repair
- Cooling and heating
- Injection system (gasoline)
- Fuel system (diesel)
- Fuel system
- Exhaust system
- Ignition system
- Transmission
- Clutch
- Transmission
- Chassis
- Brake system
- Suspension
- Steering
- Body
- Interior (all models)
- Interior (since 1997)
- Interior (since 2001)
- Exterior
- Doors and windows
- Electrical equipment
- Equipment and devices
- Power devices
- Windshield wipers and washers
- Headlights and lighting
- Electrical circuits

