Station wagon
Removing
Note. Notation «oben» (top) And «unten» (bottom) refer to the closed position of the tailgate.
1. Open the tailgate.
2. Remove the clip from the holes on the tailgate.
3. Insert a plastic wedge, e.g. HAZET 1965-20, into the middle of the gap (arrow illustration) between the side and bottom frame trims and detach the trim pieces from the clip connections.
Note. The cladding elements in this place are glued together.
4. Partially separate the lower frame trim (2) from tailgate trim (3), by pulling hard on it, and using a plastic wedge.
5. Pull the plastic hook from the clip holders on the tailgate trim. To do this, insert a screwdriver into the gap between the door trim and the frame trim. Disconnect the plastic hook by hitting the screwdriver with a hammer.
Note. The plastic hook may break in this case.
6. Place your hand between the tailgate lining and the door and pull 6 clips in succession with a strong jerk (arrows in the illustration). If necessary, use a plastic wedge.
7. Remove the cladding (1) together with side frame trim (2).
Note. The lower part of the side trim must be removed from the side trim on the rear window by moving away from the window.
8. Detach the side trim (1) on the rear window with a plastic wedge of 5 clamp holders (2). (3) – the top facing of a back window.
9. Detach 3 plastic strips (3) from compounds (3) and separate the side trim of the rear window (4) from the top of the window (1).
10. Disconnect the rear window top trim (1) strong pull from 6 clamp holders (arrows in the illustration) and take it off.
Installation
1. Pull the spikes of the metal holders of the upper trim of the rear window from the plastic tabs on the trim and press into the holes in the tailgate.
2. Reinstall the top and left rear window trims.
3. Insert the right facing of a back window at the right facing and fix.
4. Connect the rear window trim to the side trim of the frame on the tailgate so that the side trim of the frame fits into the side trim at the rear window. Push the clips into the holes.
5. Install the frame trim on the lower edge of the tailgate. At the same time, connect the side trim of the frame with the bottom one and dock the plastic hooks with the tailgate trim.
6. Push the clips into the holes in the tailgate.
Sports Coupe
1 - Handle bar; 2 - Bottom lining; 3 - Locking cable button; 4 - Side facing of the frame; 5 - Locking bracket; 6 - Upper frame lining; 7 - Locking bracket; 8 - Cover; 9 - Central lining; 10 - Locking foot; 11 - Screws; 12 - Cover; 13 - Decorative strip
Removing
Note. Notation «oben» (top) And «unten» (bottom) refer to the closed position of the tailgate.
1. Open the tailgate.
2. Remove the expander clip from the handle bar (1).
3. Remove the 2 tabs from the handle opening and pull the handle bar out of the tailgate.
4. Pull the bottom trim (2) down from the tailgate and remove.
5. Turn out the button (3) lock cable of the right and left shelves from the side window trim.
6. Separate and remove the frame side trim using a plastic wedge, e.g. HAZET 1965-20 (4) on the right and left at the rear window from the bracket holders (5).
7. Detach the top trim (6) from the bottom of the bracket holders (7) and lift up the cover. Do not break the plastic strips inside.
8. Detach the cover (8) from the center lining of the tailgate (9). At the same time, place the plastic wedge at the bottom and disconnect the cover from the three holders (10).
Note. Lid (8) The illustration is enlarged.
9. Remove the screws (11) at the back of the lid and at the bottom of the cladding (9).
10. Disconnect facing below and remove it upwards from a back door.
Installation
1. Insert the center trim at the bottom into the guides and lock into place. Attach the trim to the tailgate.
2. Further installation is carried out in the reverse order of removal.