Axles front and rear car Mercedes G-Class (W463)

General information about bridges
General information The vehicle is driven by transmitting torque from the axle differentials to the drive wheels of the front and rear axles via drive shafts (front...

Checking and adjusting the level / changing the oil in the bridge assemblies
Note: Checking and replacement must be performed with the axle gearbox warmed up. Front axle Location of the filler/inspection (1) and drain (2) plugs of the front axle...

Checking the grease packing of the pivot housings of the front axle pivot assemblies
The pivot housings of the front axle pivot assemblies are equipped with threaded plugs (1) 1. To check the hinge housing of the right drive shaft, the wheels should be...

Checking and adjusting the play of the front axle wheel bearing
1 - Brake pads 2 - Protective cover 1. Jack up the front of the car and place it on supports. Remove the corresponding front wheel. 2. Press the brake pads (1) away from...

Checking the concentricity of the seating of the connecting flanges of the main gear drives
Attention! Each time a connecting flange is removed, the resistance to rotation of the corresponding axle assembly (without wheels) must be measured - the brakes must be...

Replacing the seals of the main gear drive pinions
Installation details of sealing elements of the main gear drive pinion 1 - Adjusting washer; 2 - Ring; 3 - Oil deflector; 4 - Compression ring; 5 - Sealing ring; 6 -...

Removal and installation of main gear drive pinions
Front axle Front axle main gear pinion installation details 1 - Assembly of the differential with the driven gear of the main transmission; 2 - Nut; 3 - Connecting...

Removal, installation and adjustment of actuator cylinders and components of the drive mechanism of the interwheel differential lock
Front axle Slave cylinder Installation details of the slave cylinder (1) of the front axle differential lock drive Adjusting the slave cylinder (1) of the front axle...

Disassembly and assembly of the differential lock actuator cylinder
Front axle Design of the actuator cylinder of the front axle interwheel differential lock drive 1 - Pressure switch sensor; 2 - Lid; 3 - Cylinder; 4 - Springs; 5 -...

Removal and installation front wheel hubs
Front Wheel Hub Installation Details 1 - Sealing element holder; 2 - Upper wheel pivot bolt; 3 - Steering knuckle; 4 - Adjusting washers; 5 - Hinged casing; 6 - Hub; 7 -...

Disassembly and assembly of front wheel hubs
Front wheel hub assembly design 1 — Hub 2 - Polyurethane sealing ring 3 - Tapered roller bearing 1. Remove the hub (1) (see Section Removal and installation front wheel...

Removal and installation front axle drive shafts
Installation details of the hinge housing assembly with the drive shaft 2 - Sealing element holder; 3 - Upper wheel pivot bolt; 4 - Steering knuckle; 5 - Assembling the...

Adjusting the bearings of the swivel units
Construction of the rotary unit 1 - Pivot lever; 2 - Upper wheel pivot bolt; 3, 6 - Distance rings; 4 - Adjusting washers; 5 - Hinged casing Centering the Pivot Lever...

Disassembly and assembly of the front axle hinge housing
Hinge Cover Installation Details (1 of 2) 1 - Hinged casing; 2, 5 - Outer races; 3, 6 - Tapered roller bearings; 4 - Seal; 7 - Sealing ring Hinge Cover Installation...

Disassembly and assembly of the drive shaft
Drive shaft design 1 - Clamps; 2 - Dust cover; 3 - Spring washer; 4 - Hinge; 5 - Bushing 1. Remove the drive shaft (see Section Removal and installation front axle drive...

Removal and installation axle shafts
Rear axle shaft installation details 1 - ABS sensor; 2 - Mounting screws; 3 - Bearing cover; 4 - Half shaft; 5 - Rear axle housing sleeve 1. Remove the parking brake...

Disassembly and assembly of the axle shaft
Rear axle half shaft design 1 - Half shaft; 2 - Bearing cover; 3 - Seal; 4 - Gasket; 5 - Brake shield; 6 - Tapered roller bearing; 7 - Rectangular section sealing ring;...

Removal and installation of interwheel differential assemblies with driven gears of final drives
Front axle Front Axle Differential Assembly Installation Details 1 - Lid; 2 - Mounting brackets; 3 - Assembly of the differential with the driven gear of the main...

Disassembly and assembly of interwheel differentials
Front axle Front axle interwheel differential design 1 - Driven gear of the main transmission; 2 - Tapered roller bearings; 3 - Differential box; 4 - Side gears; 5 -...

Checking the correct engagement of the main transmission gears
The load when checking the correct engagement of the main gear gears is provided by braking the driven gear using a special device (601 589 01 40 00). 1. Lubricate a...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code

W463 (1999-2019)