Engine cooling system Mercedes G-Class (W463)

Cooling, Heating and Ventilation System Specifications
Engine cooling system All models of the vehicles considered in this Manual are equipped with a positive pressure engine cooling system with thermostatic control of the...

Antifreeze is a means of protection against freezing
Antifreeze - a means of protection against freezing Warning! Do not allow antifreeze to come into contact with exposed areas of the body or painted surfaces of the...

Coolant Replacement — General Notes
Warning! Do not allow antifreeze to come into contact with exposed areas of the body or painted surfaces of the vehicle. Wash away accidental splashes immediately with...

Checking the cooling system cap, replacing the hoses
Checking the lid Checking the cooling system cap A - Bayonet type cover; 2 - Tester; 3 - Nozzle cover; 4 - Nozzle; 5 - Cooling system cover; 6 - Pressure reducing valve;...

Checking the Thermostat
Checking without removing the thermostat 1. Before removing and checking the thermostat, make sure that the engine cooling problems are not due to insufficient coolant...

Removal and installation the thermostat
Petrol models Installation details of thermostat assembly on petrol engines 1 - Thermostat housing; 2 - Sealing ring; 3 - Mounting bolts; 4 - Clamp; 5 - Cooling tract...

Removal and installation the cooling system radiator
Petrol models Radiator installation details for petrol models 1 - Crankcase protection; 2 - Fixators; 3 - Washers; 4 - Bolt; 5 - ATF cooling line; 6 - Cooling system...

Removal and installation the expansion tank
Petrol models Expansion tank installation details for petrol and diesel models with 628 series engine (1 of 2) 1 - Ventilation hose (2 pcs) 3 - Bolts 4 - Expansion tank...

Removal and installation the cooling system fan assembly
Petrol models Assembly of the impeller with a viscous clutch Installation details of the fan impeller with a viscous clutch on gasoline models 1 - Holder; 2 - Drive belt...

Removal and installation the water pump
Petrol models Water pump installation details for petrol models 1 - Assembly of the impeller with a viscous coupling; 2 - Auxiliary drive belt; 3 - Fan assembly casing;...

Removal and installation low-temperature cooler (M612)
Installation details of low-temperature cooler on diesel models with M612 engine 1 - Air intake sleeve; 2, 3 - Cooling tract hoses; 4 - Cooling tract overflow line; 5 -...

Removal and installation the engine block heater
Engine Block Heater Installation Details (models 463.322/323, code HP1) 1 - Electrical wiring connector; 2 - Spring lock; 3 - Lid; 4 - Engine block heater wiring; 5 -...

Removal and installation of additional heater STH
Additional heater installation details (models 463.250/323, code H12) 1 - Cooling tract outlet hose; 2 - Cooling tract inlet hose; 3 - Fuel line; 4, 5 - Couplings; 6 -...

Removal and installation the circulation pump of the additional heater STH
Circulation pump installation details (models 463.250/323, code H12) 3 - Return hose of the cooling tract (heater); 4 - Cooling tract inlet hose; 5 - Heater cover; 8 -...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More similar sections for repairing other models

☛ Power unit: Cooling and heating car Mercedes W168 (1997-2004)
☛ Power unit: Cooling and heating car Mercedes 190 (W201) (1982-1993)
☛ Power unit: Cooling system car Mercedes W124 (1984-1995)
☛ Power unit: Cooling system car Mercedes W163 (1997-2005)
☛ Power unit: Cooling system car Mercedes W126 (1979-1991, petrol)
☛ Petrol engines 2.8 l: Cooling system car Mercedes Vito 1 (1996-2003)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code

W463 (1999-2019)